add Sensoren auslesen

include/MessenSensoren.h

@@ -8,6 +8,10 @@ void MessenSensoren(void);
 
 
 
+// nicht schoen aber funktioniert
+#include "hseSensorProtocol.h"
+extern HseSP hse;
+
 
 
 

src/MessenSensoren.cpp

@@ -6,25 +6,38 @@
 #include "myi2c.h"
 #include "bme280.h"
 #include "bh1750.h"  
+#include "hseSensorProtocol.h"
 
 #define I2C_POWER 5         // bei Feather M0
 
 
+// hse-Protokoll Datensatz
+HseSP hse(2, 60);
+
+
 void init_Messen(void)
 {
+int i;
 
+Serial.println("PowerOn I2C");
 // I2C Power einschalten LoRa Transponder
 pinMode(I2C_POWER,OUTPUT); 
 digitalWrite(I2C_POWER, HIGH);
-delay(10/8);
+delay(20);
 
 Wire.begin();
 
 // Hardware detection, liste was angeschlossen ist
+Serial.println("I2C Hardware detection");
 
 if ( I2C_Test(BME280_ADR) != 0xFF )
    {
-   Serial.println("BME280 gefunden"); 
+   Set_I2C_Adresse(BME280_ADR);
+   i = I2C_read8(BME280_REGISTER_CHIPID);
+   Serial1.print(F("BMx280 Chip ID = 0x"));
+   Serial1.print(i,HEX);
+   if ( i== 0x58) Serial1.println(F(" = BMP280"));
+   if ( i== 0x60) Serial1.println(F(" = BME280"));
    }  
 
 if ( I2C_Test(0x77) != 0xFF )
@@ -49,11 +62,87 @@ if ( I2C_Test(0x23) != 0xFF )
    Serial.println("BH1750 gefunden"); 
    BH1750_Init(); 
    }    
-
+Serial.println("ende");
 }
 
 //--------------------------
 void MessenSensoren(void)
 {
+int i,status, error;
+float t,p,h;
+long lVisLux; 
+
+
+Set_I2C_Adresse(BME280_ADR);
+i = I2C_read8(BME280_REGISTER_CHIPID); 
+
+bme280_readCoefficients();
+
+if ( i== 0x58)
+   {
+   I2C_write8(BME280_REGISTER_CONTROL, 0x3F); 
+   delay(50);  // gib ihm Zeit zum messen
+   }
+
+if ( i== 0x60)
+   {
+   //Set before CONTROL_meas (DS 5.4.3)
+   I2C_write8(BME280_REGISTER_CONTROLHUMID, 0x05); //16x oversampling 
+   I2C_write8(BME280_REGISTER_CONTROL, 0xB7); // 16x ovesampling, normal mode 
+   delay(100);  // gib ihm Zeit zum messen
+   }
+// 35ms reicht beim BMP280
+// 75ms warten bis BME280 den Druck gemessen hat
+
+//----------------
+ t = bme280_readTemperature();
+ p = bme280_readPressure()/100.0;
+ h = bme280_readHumidity();
+ I2C_write8(BME280_REGISTER_CONTROL, 0x3C); // Sleep Mode
+*/
+
+// such BH1730
+if ( I2C_Test(0x29) != 0xFF )
+   {
+   BH1730_Init(); 
+   lVisLux = BH1730_ReadLux();
+   // BH1730_ReadIR();  will keiner mehr wissen
+   }
+   
+// such BH1750
+if ( I2C_Test(0x23) != 0xFF )
+   {
+   // BH1750 = HY30 Licht Sensor
+   BH1750_Init(); 
+   lVisLux = BH1750_ReadLux();
+   }    
+   
+ if ( lVisLux > 65535) lVisLux = 654321;
+
+
+Serial.print(F("Temp = "));
+Serial.println(t);
+Serial.print(F("Druck = "));
+Serial.println(p);
+Serial.print(F("Feuchte = "));
+Serial.println(h);
+
+Serial.print(F("Vis = "));
+Serial.println(lVisLux);
+
+
+  hse.reset();
+//Ein Klimasensor hinzufügen
+  HseSP::ClimateSensor_t cs;
+  cs.Temperature = t; //°C
+  cs.Humidity = h;     //%
+  cs.Pressure = p;   //hPa
+  cs.Illuminance = lVisLux;   //lux
+  hse.addClimateSensor(&cs);
+
+//  hse.addVoltage(fUb/1000.0);  // in Volt
+//  hse.addCounter(uiOnStd);    // Zeit On
+
+
 
 }